Simer 12356 Manuel du propriétaire télécharger pdf (Page 3)

For assistance, call Simer Customer Service at 1-800-468-7867 / 1-800-546-7867

Installation 3

To reduce risk of electric shock,

pull plug before servicing. This pump has not

been investigated for use in swimming pool

areas. Pump is supplied with a grounding con-

ductor and grounding-type attachment plug. Be

sure it is connected only to a properly grounded

grounding-type receptacle.

Where a 2-prong wall receptacle is encoun-

tered, it must be replaced with properly

grounded 3-prong receptacle installed in accor-

dance with codes and ordinances that apply.

13. All wiring should be performed by a qualified

electrician.

14. Make certain power source conforms to require-

ments of your equipment.

15. Protect electrical cord from sharp objects, hot

surfaces, oil, and chemicals. Avoid kinking cord.

Replace or repair damaged or worn cords

immediately.

16. Do not touch an operating motor. Modern motors

can operate at high temperatures.

17. Do not handle pump or pump motor with wet

hands or when standing on wet or damp surface,

or in water.

Hazardous voltage can shock, burn or

kill. If your basement has water or moisture on

floor, do not walk on wet area until all power has

been turned off. If shut-off box is in basement, call

electric company or hydro authority to shut-off ser-

vice to house, or call your local fire department for

instructions. Remove pump and repair or replace.

Failure to follow this warning can result in fatal

electrical shock.

Do not lift pump by power cord.

INSTALLATION

1. Install pump in sump pit with minimum diameter

of 14" (356mm). Sump depth should be 22"

(559mm). Construct sump pit of tile, concrete,

steel or plastic. Check local codes for approved

materials and for proper installation.

2. Install pump in pit so that switch has maximum

possible clearance.

3. Pump should not be installed on clay, earth or

sand surfaces. Clean sump pit of small stones

and gravel which could clog pump. Keep pump

inlet screen clear.

NOTICE: Do not use ordinary pipe joint com-

pound on plastic pipe. Pipe joint compound can

attack plastics.

4. Wrap elbow with Teflon

tape and thread it into

the pump discharge.

5. Install discharge plumbing in the elbow. Use rigid

plastic pipe and wrap threads with Teflon

tape.

Screw pipe into pump hand tight plus 1-1/2 turns.

Risk of flooding. If a flexible dis-

charge hose is used, make sure pump is

secured in sump to prevent movement. Failure

to secure pump may allow pump movement,

switch interference and prevent pump from

starting or stopping.

6. To reduce motor noise and vibrations, a short

length of rubber hose (1-7/8" (47.6mm) I.D., e.g.

radiator hose) can be connected into discharge

line near pump using suitable clamps.

7. Install an in-line check valve to prevent flow

backwards through pump when pump shuts off.

NOTICE: If your check valve is not equipped with

an air bleed hole to prevent airlocking pump, drill

a 1/8" (3.2 mm) hole in discharge pipe just above

where the discharge pipe screws into the pump

discharge. Be sure the hole is below the waterline

and the check valve to prevent air locks.

8. Power Supply: Pump is designed for 115 V., 60

Hz., operation and requires a minimum 15 amp

individual branch circuit. Both pump and switch

are supplied with 3-wire cord sets with ground-

ing-type plugs. Switch plug is inserted directly

into outlet and pump plug inserts into opposite

end of switch plug.

Pump should always be electrically

grounded to a suitable electrical ground such

as a grounded water pipe or a properly grounded

metallic raceway, or ground wire system. Do

not cut off round ground pin.

9. If pump discharge line is exposed to outside sub-

freezing atmosphere, portion of line exposed

must be installed so any water remaining in pipe

will drain to the outfall by gravity. Failure to do

this can cause water trapped in discharge to

freeze which could result in damage to pump.

10. After piping, check valve and float switch have

been installed, the unit is ready for operation.

11. Check the pump operation by filling sump with

water and observing pump operation through one

complete cycle. For switch settings see the Electrical

and Switch Specifications chart on Page 2.

Failure to make this operational

check may lead to improper operation, prema-

ture failure, and flooding.

E.I. DuPont De Nemours and Company Corporation, Delaware.

1 2 3 4 5 6 7 8 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Simer 12356 Manuel du propriétaire Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à eau Simer 12356